• Water-based product for easy application and repair.
• Thixotropic behavior that self-levels when applied on both horizontal surfaces
as vertical.
• Forms continuous elastic membranes without joining joints.
• Permeable to water vapor, allowing perspiration of the surfaces where it is applied.
• Excellent resistance to environmental humidity, atmospheric pollutants and solar exposure (U.V.).
• The white color acts as a solar reflector, reducing the interior temperature of the building considerably.
• Very good adhesion on porous substrates (concrete, mortar, etc.) and non-porous substrates (cement tiles, wood, rusty metal, galvanized steel, etc.)

Before applying the product, check that the support is clean and free of traces of oil, grease, silicone, contaminating waxes or soil materials. In case you need
repair apply suitable repair mortars.
Apply at room temperature between +5 ºC and 35 ºC. The temperature of the support must be between +5 ºC and 35 ºC. The support must be dry and with relative humidity < 85% (Maximum residual humidity of the support < 10%).
It is important to control the dew point to prevent condensation and
Avoid whitish areas on the coating.
It is necessary to start from a porous concrete support, without grout and free of liquids.
curing. Minimum compressive strength of concrete: 15 N/mm2. Minimum resistance
tensile strength of concrete: 1 N/mm2. 28-day hardness of concrete: 15 MPa.
Mix the two components in the recommended proportion: 25 parts of
component B for every 0.250 parts of component A. Beat component B well in its
container, then add component A and mix with a low-pressure mechanical stirrer.
revolutions (300-400 rpm) a minimum of 2-3 minutes until reaching a product
homogeneous. If overmixed, occluded air bubbles may appear. Once
Once the two components are mixed, it is ready for use. Application open time
(Pot Life) is 45 minutes at 20ºC.

The product is ready for use once the two components have been mixed.
It can be diluted up to a maximum of 5-10%.
Apply with a roller in very thin layers of In case of waterproofing applications, the minimum consumption will be 1.5-2 Kg/m2, always armed with FUTUR ARMOR POLYESTER 50 G between layers.
For waterproofing and protection of metal sheets and polyurethane foam, the consumption will be approximately 1.5 Kg/m2, assembling only the singular points.

In the case of protective paint, the consumption will be 0.8-1.2 Kg/m2 without assembly.
Repainting will be done once the previous layers are dry to the touch, approx. Once 2-4 hours have passed.

Maintenance and cleaning: To maintain the appearance of the floor after application, all spills must be removed immediately after they have occurred. The floor must be cleaned regularly using rotating brushes, high-pressure cleaners, vacuum cleaners, using neutral detergents and appropriate waxes.

Once the container is opened, we recommend its complete consumption. Once the two components have been mixed, the mixture obtained must be applied, respecting the pot-life.
Stable for 12 months from its manufacturing date, in its original, well-closed and undamaged container. Store in a dry and cool place at temperatures between +5ºC and +25ºC.
Incorrect treatment of cracks and singular points can lead to a reduction in the useful life of the membrane.

To clean materials and utensils, use water before the product hardens. Once the product has hardened it can only be removed by mechanical means.

• Very useful in all types of construction companies, quick repair contracts, general masonry, community maintenance, building repair and restoration, waterproofing, etc.
For application in the waterproofing and protection of:
• Polyurethane foam.
• Inclined and inverted roofs.
• Lightweight metal or fiber cement inclined roofs.
• Exterior walls, perimeter walls, vertical and horizontal surfaces on roofs, facades, etc.
Applicable on concrete surfaces, fiber cement, cement tiles, wood, rusty metal, galvanized steel, etc.